Drywall taping: Tips right from a pro

Drywalls in your home is not a pleasant sight in your home. However, there is more disgusting sight than drywall, and that is a poorly finished attempt while trying to fix drywall with drywall taping.

The expert makes it very easy as they move quickly, slathering compounds on each of the nail holes and joints. And what they leave behind is ultra-smooth and great looking walls. Taping the drywalls is not an easy task to do. Giving the flawless finish to the walls is not everyone’s cup of tea. However, with the proper tools, process and a few tips from the expert may help to finish drywall taping like a pro in no time.

Considering you know the first two aspects to do the job correctly, here are a few tips right from the experts that will help you to finish the work just like them.

Dos of drywall taping:

  1. Put the power drill in work

Drywall mud has to be smooth, and you should make it free from the lumps before beginning the process. Mixing the powder component with water using your hand is a very time-consuming work. Plus, it may not give you the perfect finish. You may not be able to cancel out all the lumps of the powder, especially if you do not have the patience to stir it long enough. So, instead of doing this by hand, use the power drill to blend the compound. While you are using the power drill to stir, make sure you mix enough to send the mixture into a peanut butter consistency.

BLACK+DECKER 20V MAX Cordless Drill / Driver with 30-Piece Accessories (LD120VA)

  1. Prefill the wide joints

Gaps more than 1/8 inches can give an amateur appearance. Fill these wide joints before you get into taping. The compounds you are using in making the mixture tends to shrink. So, if you use the paper tapes at the same time you applied the initial coating, the compound may warp the paper tape. But, when you fill these gaps earlier and left them to dry before taping, the compounds in the holes will not affect the tape negatively. While prefilling the mixture in the broader gaps, press it carefully and directly into the joints. You then should carefully wipe off the excess with the edge of a putty knife. Leave the joints for at least 24 hours before you put on the first taping coat.

Loctite TITE FOAM Insulating Foam Sealant, Gaps & Cracks, 12-Ounce Can

  1. Take steps to reduce the wet compound mess

You will surely find some splatters while going to tape the drywall. These splatters will be in everywhere. It will be everywhere in the rooms, even on you. So, wear protective eyewear, a hat. Try to wear old clothing that you can toss once after you are done with the job. Remove all the furniture items from the room and cover the ground with canvas drop.

3M SHR High Strength Small Hole Repair Kit with 8 fl. oz Plus Primer, Self-Adhesive Patch, Putty Knife and Sanding Pad, 1 tub, White

  1. Cut the bubbles formed into the tape

After you are done with the dried initial compounds and taping, now it’s time to check the bubbles on the tape. Bubbles formed in the tape means either there is not enough mud to fill the gap under the tape or you haven’t pressed the tape firmly against the wall. Use a sharp knife and cut the part of the tape. Apply mud on the region again, smoothen it and leave it to dry.

Buddy Tools TapeBuddy Drywall Taping Tool – Mess Free DIY One Step Drywall Tape and Joint Compound Application

  1. Apply multiple coatings instead of thicker but lesser coats

Try using various layers. Wait, not the thicker coatings but, the thinner. This is the secret of professional drywall taping. The professionals use multiple thinner coatings than thicker and fewer coats because of that although it takes time to dry at the same time helps to reduce thetime of your sanding.

DON’Ts of drywall taping:

  1. Do not buy the wrong mud for the project

This is the most usual problem people create for themselves. If you are not that experienced in these cases, try to use a setting or all-purpose compound. However, do not use them for the final coating. You can instead shift to a topping compound for the final coat.

  1. DO NOT overlap the drywall tips

Applying a single layer of the paper tape will work, and you don’t need to overlap the tapes. If you do, there are high chances of a bulge in the walls. We guess you may not like the idea of having bumps on your walls.

  1. Don’t skip the screw hole while applying each coat

Never skip a hole in your wall. All it takes is a dab of mud and a few seconds or minutes to fill the screw holes and the nail holes properly. Do not skip them.

  1. Do not apply the next mud coating over the bits of the dry compound

While coating the walls with the compound, it is prevalent to end up with some ridges. These ridges occur because of the excess mud that escaped the edges of the knife and got dried there. No worries. Push the edge of a knife against the wall and scrape it off. Then you can freely apply the second coating. But do not put the second coating over the flecks.

  1. Do not sand before protecting yourself properly

Do not start sanding before you have protected yourself properly. Tape plastic sheeting on the doorways, registers and vents. Prevent the drywall dust from entering in the other rooms. Wear, clothing, hat and eyewear. Also, wear a respirator mask.

Drywall taping can be proven extremely invasive if done without following the steps. However, following them will get you a finish like a pro. Be safe and finish drywall taping like a pro.  

Total Page Visits: 263 - Today Page Visits: 4
Enable registration in settings - general